I am posting an early design sketch of a 2m WSPR beacon. Here are the key points: 25 MHz HCI 0.5ppm TCXO powering the Si5351 module instead of the 26 MHz TCXO. If this fails, we can use a 10 MHz OCXO instead (a bit out of spec but works fine). Tokmas CID10N65F GaN FET might work @ 144 MHz as the 'final'. If not, use Mitsubishi RD15HVF1-501 MOSFET as backup. ...
I am posting an early design sketch of a 6m WSPR beacon. Here are the key points: 25 MHz HCI 0.5ppm TCXO powering the Si5351 module instead of the 26 MHz TCXO. If this fails, we can use a 10 MHz OCXO instead (a bit out of spec but works fine). Tokmas CID10N65F GaN FET should work @ 50 MHz TI UCC27614 or Onsemi NCP81074 gate driver Results: To be built and tested soon! ...
This ~1W to ~5W WSPR beacon runs continuously on the 10m band. It handles extreme environmental temperatures pretty well (it is 42°C plus here). Our article on this beacon's design and operation will appear in the May/June 2025 issue of the QEX magazine soon. References: http://www.carnut.info/WSPR_Tx/WSPR_Tx.htm
Ismo (OH2FTG) recently introduced me to a bunch of Tokmas RF parts. Out of these, the Tokmas CID10N65F GaN FET stood out. It seems to have a lot of potential (for HF + 6m) at a very low price point. This RF MOSFET part can be purchased from LCSC. It seems Tokmas CID10N65F has the potential to completely replace the RD16HHF1 part from Mitsubishi Electric! Datasheet excerpt: The full datasheet is available here. ...
I have designed, built and tested an all-HF WSPR beacon which produces 1W @ 5V and is rugged and cost-effective. Power consumption: Around 420mA @ 5V. Cost: Around 500 INR. Time to build: Less than 30 minutes. The files for this project are published here for personal (non-commercial) usage. For a 5W (QRO) WSPR beacon, please hold on for our upcoming QEX magazine article ;) Special shoutout goes to Brad (K1TE) for always pushing me to do better - thank you! ...
I found this 60W Electronic Load to be quite useful for testing small power adapters and supplies. While it is possible to homebrew an adjustable electronic load we recommend getting this electronic load module or a better-but-costlier one like the UNI-T UTL8212+ electronic load. You can stress-test power supplies using this electronic load quite easily and conveniently. It turns out that the Orange branded 12V 2A or 3A adapters from Robu are really trash. The output voltage drops to less than 2V when the load current is increased to around 1A. This is NOT the first time that the Orange branded stuff has turned out to be of poor quality. At the end, you get what you pay for. ...
I have built probably the easiest, reasonably rugged and most cost-effective 100mW WSPR (or FT8) beacon. Here is my quick and dirty build with whatever I had laying around: We have replaced the traditional expensive Mini-Circuits transformer with a cost-effective Bourns coupled inductor. Power consumption: Before RF generation starts -> 20mA @ 5v. After RF generation starts -> 52mA @ 5v. So the power input consumed in the RF generation process is more than 150mW it seems (which is good). ...
The Easy WSPR Encoder can be accessed here. Update: You may find this software more useful.
Bharath and I have written our thoughts on building a RF lab on a budget. It is geared towards homebrewers and new amateur radio operators. We maintain this documentation here. Have fun! :-)
The Easy FT8 Encoder can be accessed here. In the near future, we want to add the K1JT's original FT8 encoder functionality as well. Update: https://pengowray.github.io/ft8play/ is crazy good!